Car Audio Amplifier Monoblock in Marietta, GA
When you are seeking Car Audio Amplifier Monoblock in Marietta, GA, you should consider our car audio store. One of the reasons hundreds of car audio enthusiasts visit our site every week searching for things like car stereo best buy is not because we are the best known but because stereo enthusiast who like to work in his/hers vehicle knowt that our car audio store offers a wide selection of low prices car subwoofers, car amplifiers, car speakers and electronics with FREE shipping.
Whether you’re looking for Car Audio Amplifier Monoblock Marietta, GA or 10-Inch Car Subwoofer we know you will find our collection adequate. That is because we make a great effort cooshing the products we offer so that you have the easiest car stereo installation experience and top rated car audio system you can be proud of and your friends would want to purchase. So, tell all your friends for Car Audio Amplifier Monoblock in Marietta, GA take a look at ThunderEletronics.Net for great prices and lastest technology for Car Audio Amplifier Monoblock in Marietta, GA or 10-Inch Car Subwoofer Box we are sure you will pleased with the inventory at our website. For the best prices on car audio installation and quick expedited shipping, and misleading advertising you can count on Thunder Electronics.
Best Selling Car Audio Amplifier Monoblock Near Marietta, GA
- Blaupunkt 1500 Watt Monoblock Amplifier
- Max power output: 1500 watts / RMS Output Power Rating: 4 ohms: 120 watts x 1 channel / 2 ohms: 200 watts x 1 channel / Frequency Response: 10Hz - 30kHz
- Signal-To- Noise Ratio: >96 dB / Voltage Supply: 11 - 16V DC / Gain Adjust: 200mV-8V
- Total Harmonic Distortion:
- Power - 2000 Watts MAX x 1 @1-Ohm, 1000 Watts RMS x 1 @1-Ohm, 650 Watts RMS x 1 @2-Ohms,400 Watts RMS x 1 @4-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be...
- To keep both your car and the stereo amp safe, this ZE1000.1 is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality...
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 1,600 Watts | RMS Power at 1 Ohm: 1,200 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow. Damping Factor - 150
- 3,000 watts x 1 channel max power output
- 198 watts RMS x 1 channel at 4 ohms
- 396 watts RMS x 1 channel at 2 ohms
- Designed to power vehicle subwoofer
- 330 watts RMS x 14 ohms
- preamp and speaker-level inputs
- variable bass boost
- The amp includes preamp- and speaker-level inputs,you can installin almost any vehicle, even one with a factory radio.
- 4,000 watts x 1 channel max power output
- 2,800 watts RMS x 1 channel at 1 ohm
- 2,000 watts RMS x 1 channel at 2 ohms
- 1,000 watts RMS x 1 channel at 4 ohms
- DIMENSIONS: 10.43" x 9.21" x 2.25", WEIGHT: 4.37 lbs
- SPECS: Monoblock, Class A/B, 2Ω Stable, MOSFET Power Supply, 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms
- SPECS CONT'D: Low Pass Filter, Bass Boost, Input Sensitivity, Illuminated Logo, Thermal, Short and Overload Protection Circuits, Remote Subwoofer Control
- INPUTS/OUTPUTS: RCA & Speaker Level Inputs
- 1 channel x 3,500 watts @ 1 ohm
- 1 channel x 1,750 watts @ 2 ohms
- 1 channel x 875 watts @ 4 ohms
- Operates in mono mode only
- Digital Class-D Mono Block Amplifier: Class D topology ensures high efficiency with big power and a small footprint. This single 1-channel amplifier was built for driving subwoofers and subwoofer systems,...
- Compact and Sturdy Design: Precise sound control with our durable metal potentiometer, designed for long-lasting reliability and exceptional tonal adjustments.
- Robust Unregulated Power Supplies: The power supply circuitry adopts advanced pulse width modulator integrated circuits that are designed to offer improved performance and efficiency.
- Remote Bass Controller Included: Provides remote level control of bass from listening position. With a sleek flush-mount knob for ease of installation.
- Powerful Performance: The AMP1501PRO delivers an impressive 563-watt RMS and a maximum output of 1500 watts, providing a significant power boost for a vibrant and dynamic driving soundtrack.
- Space-Efficient Design: With compact dimensions (7.1" x 7.5" x 2.1"), this amplifier seamlessly integrates into any trunk, optimizing space while delivering high-quality audio performance.
- High-pass and low-pass filters: integrated high- and low-pass filters on the rear panel allow you to set the crossover frequency between the subwoofer and speakers.
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Power - 1000 Watts MAX x 1 @1-Ohm, 500 Watts RMS x 1 @1-Ohm, 350 Watts RMS x 1 @2-Ohms,200 Watts RMS x 1 @4-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be...
- To keep both your car and the stereo amp safe, this ZE500.1 is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality...
- This Class D Monoblock Amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this mono...
- This cobalt subwoofer amplifier for car speakers is able to power loads of 1 Ohm on a continuous basis without facing any difficulties like overheating, making extra sounds. This Class D amplifier is...
- The monoblock subwoofer amplifier for car stereo speakers with mosfet power supply comes with low/high level inputs. A low level (RCA) input is measured in voltages. A high level (+/- wire) input is...
- The monoblock bass boost amplifier has features like - Frequency Response: 10~250HZ, Low Pass Filter, Bass Boost, Subsonic Control, Remote Bass Knob, MOSFET Power Supply, Thermal Protection, Phase Shift.
- The HD line offers Monoblock amplifiers that operate at 1, 2, or 4 Ohms, making them perfect for a variety of setups, from subwoofers to tweeters.
- The Taramps HD 3000 delivers 3000 Watts RMS. This monoblock amp offers exceptional flexibility and now includes compatibility with Monitor Level Remote.
- The Positive/Negative Power Cable is 4 AWG | The Output Cables Wire Gauge is 9 AWG | The Remote Cable is 18 AWG | The Circuit Breaker or Fuse is 150A.
- Perfect for various car audio setups, this perfect amplifier comes equipped with a Crossover, Input/Output settings and a precise Level Control.
- Marine Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 1,200 Watts | RMS Power at 1 Ohm: 800 Watts
- Fully Marinized with Waterproof Coating on Circuit Board & Rust Proof Painting on Mechanical Case
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Car audio amplifier 450 watts RMS at 2-ohm load (14.4v); 300 watts RMS at 4-ohm load (14.4v);
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 2-4 Ohm Stable - Able to continuously power loads of 2-4 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to...
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- Power - 2000 Max x 1 @2 Ohms, 1000 Max x 1 @4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its...
- Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your...
- Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- 2Ω stable; PWM MOSFET Power supply
- RCA and speaker level inputs
- Variable bass boost 0-12dB; Variable Low-pass filter 50-250Hz; Variable input gain control 0.2-8V
- Full range or LPF mode switch
- Digital Class-D Mono Block Amplifier: Class D topology ensures high efficiency with big power and a small footprint. This single 1-channel amplifier was built for driving subwoofers and subwoofer systems,...
- Compact and Sturdy Design: Precise sound control with our durable metal potentiometer, designed for long-lasting reliability and exceptional tonal adjustments.
- Robust Unregulated Power Supplies: The power supply circuitry adopts advanced pulse width modulator integrated circuits that are designed to offer improved performance and efficiency.
- Remote Bass Controller Included: Provides remote level control of bass from listening position. With a sleek flush-mount knob for ease of installation.
Last update on 2024-12-18 / Images Source Amazon Product API
Article Related to Car Audio Amplifier Monoblock in Marietta, GA.
Tell-Tell Signs of a Good Sounding Car Speaker
When it comes to car audio and car audio speakers, one should never consider buying them without listening to them. Preferably in a [...]
Cars With The Best Factory Sound Systems
Gather all audio enthusiasts and audiophiles; we are about to dive into some cars with the best factory sound systems. Usually, most car [...]
Are Factory Premium Car Audio System Worth it?
Over the last few years, we have seen a trend emerge of mergers between car manufacturers and audio brands with a [...]
Buick Grand National Car Stereo System
Since I was in high school, I always wanted to have a Buick Grand National. Maybe it is just me, but I always thought that car looked super mean. And yes, while Buicks are considered a grandma’s car those who know what a Grand National can do, will say to the contrary. Now that I have the means, I decided to find myself a Buick Grand National. After finding one in perfect condition, I went ahead and purchased it.
Since acquiring my mean black Buick, I’ve done a little bit of work on the engine. I have upgraded the turbo, install an oversize intercooler, added a high-pressure fuel pump, aftermarket wastegate, a new computer, and several other upgrades including wheels tires, suspension, and exhausts. I have to say that I like my car. However, the sound system sucks. If you’re not familiar with this car it came with a Delco 1.5 DIN cassette radio, 3 1/2 inch speakers in the dash, and 4×10 speakers in the rear deck.
As you can imagine, this is no match for the 650 horsepower engine under the hood. The problem is that with these speaker cavities, what can you do? The first thing I did was stop by car audio near me places looking for experienced installers, familiar with this vehicle. That did not work! It seems like kids nowadays are just interested in boomy car stereo systems.
After asking around, I was able to locate an old-timer who claimed to have competed in car audio with a similar vehicle. At the end of the day, I ended up having custom door panel pods built. Unlike many door pods, I had these made, so that lay over the factory door panel, and that can get removed the day I want to sell the car.
Just to be clear, I am not rich, and everything I do has a budget! So with that said I know there are people out there who are going to say that I could have done much better, and maybe will upgrade in the future but taking into consideration where I am coming from this is a huge upgrade.
The system consists of a Rockford Fosgate 5-Channel amp mounted on a custom rank that contours the left side of the truck wall being fed by the Alpine CDE-163BT Advanced Bluetooth CD Receiver. I know that nowadays kids are into everything Bluetooth. To be honest with you I don’t care much about the Bluetooth,” type of guy has to believe in the quality of the CD. The fact is until somebody can show me an MP3 with a 16-bit/44.1kHz resolution I will be sticking to CDs. I did not use the front speaker location which houses a 3 1/2 inch woofer. Instead, I opted for a pair of Q-Logic kick panels and mounted the Pioneer TS-D1330C 5.25″ D-Series Component Speaker Package on it. I chose the NEUPRO 65 V2 4 from Sundown Audio for the custom door panel. That is a 6.5″ 4-Ohm Midrange Speaker that is very shallow, and with an excellent midbass snap to it! The midbass is further enhanced because the door pod enclosure is sealed.
For the back speakers, I also avoided the factory location. Instead, I opted to use the panels above the hand rest for the rear seat. After making custom plates, I mounted a set of Pioneer TS-D1730C 6 3/4″ component speakers with the woofer in the custom plate and the tweeter flush-fitted to the side panel all the way back near to the rear window. For subs, I decided to use two Pioneer Free 12″ subs. I fabricated a reverse box with the back open and sealed against the back seat wall. You may question this, but if you hear it you agree it was the best choice.
Top Links Related to Car Audio Amplifier Monoblock in Marietta, GA.
Without a question that if searching for Car Audio Amplifier Monoblock in Marietta, GA you have many options. Even though, car manufactuerer’s like Polestar are making a lot more difficult to install aftermarket car audio you can still have a good sound system in your vehicle, and we are positive that you will be able to find a professional car audio installation place Marietta, GA that it up to the task. At Thunder Electronics we want to make this process easier be offering you the best deals on car audio in or near Marietta, GA. From Car Audio Crossovers to Preloaded Subwoofer Boxes we have what you are looking for. It is often said that music is the best way to change you mood and at ThunderEletronics.Net we want to be your best option if searching for Car Audio Amplifier Monoblock in Marietta, GA…