Car Audio Amplifier Monoblock in Tampa, FL
When you’re seeking Car Audio Amplifier Monoblock in Tampa, FL, you have to consider our car audio store. The reason a lot of stereo enthusiasts visit electronics.net every month looking for things like car stereo JVC is not because we are the cheapest but because DIY car audio enthusiast knowt that Thunder Eletronics offers a broad selection of stereos, speakers, subs, and amps with FREE shipping.
Don’t matter if you are searching for Car Audio Amplifier Monoblock Tampa, FL or Car Audio Speaker 6.5 Inch we know you will find our inventory impressive. That is because we put a lot of time and effort cooshing the products we offer so that you have the easiest car audio installation experience and a top notch car audio system you will be happy with and your friends will envi. So, tell all your friends for Car Audio Amplifier Monoblock in Tampa, FL check out Thunder Eletronics for great prices and up to date for Car Audio Amplifier Monoblock in Tampa, FL or Car Stereo Amplifier 6-Channel we’re sure you’ll content with the inventory at our site. For the best prices on car audio equalizer and quick expedited shipping, and no games you can count on Thunder Electronics!
Best Selling Car Audio Amplifier Monoblock Near Tampa, FL
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 1,600 Watts | RMS Power at 1 Ohm: 1,200 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow. Damping Factor - 150
- Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its...
- MOSFET Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss &...
- Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your...
- Blaupunkt 1500 Watt Monoblock Amplifier
- Max power output: 1500 watts / RMS Output Power Rating: 4 ohms: 120 watts x 1 channel / 2 ohms: 200 watts x 1 channel / Frequency Response: 10Hz - 30kHz
- Signal-To- Noise Ratio: >96 dB / Voltage Supply: 11 - 16V DC / Gain Adjust: 200mV-8V
- Total Harmonic Distortion:
- 4,000 watts x 1 channel max power output
- 2,800 watts RMS x 1 channel at 1 ohm
- 2,000 watts RMS x 1 channel at 2 ohms
- 1,000 watts RMS x 1 channel at 4 ohms
- 3,000 watts x 1 channel max power output
- 198 watts RMS x 1 channel at 4 ohms
- 396 watts RMS x 1 channel at 2 ohms
- Designed to power vehicle subwoofer
- Car audio amplifier with 1500 watts RMS power at 1-ohm load (14.4v); 850 watts RMS at 2-ohm load (14.4v); 450 watts RMS at 4-ohm load (14.4v); Frequency response: 0 to 320 Hz (Bass Knob Included)
- Small footprint and compact chassis makes this mono amplifier easy to install in any vehicle or car audio application; but don’t let the size fool you, this 1500 watt amplifier absolutely pounds
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Power - 2000 Watts MAX x 1 @1-Ohm, 1000 Watts RMS x 1 @1-Ohm, 650 Watts RMS x 1 @2-Ohms,400 Watts RMS x 1 @4-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be...
- To keep both your car and the stereo amp safe, this ZE1000.1 is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality...
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 388 Watts | RMS Power at 1 Ohm: 350 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow
- By Orion High Performance Car Audio
- CBT4500.1D Cobalt Series 1-Channel Monoblock Class D Amplifier
- Watts @ 1 Ohm Mono 14.4V: 1200W
- Max Music Peak Power: 4500W
- Digital Class-D Mono Block Amplifier: Class D topology ensures high efficiency with big power and a small footprint. This mono amplifier was built for driving subwoofers and subwoofer systems, maintaining...
- Small Footprint and Sturdy Design: Made it precision metal potentiometer for precise tuning and sturdy construction.
- Robust Unregulated Power Supplies: The power supply circuitry adopts advanced pulse width modulator integrated circuits that are designed to offer improved performance and efficiency.
- Remote Bass Controller Included: Provides remote level control of bass from listening position. With a sleek flush-mount knob for ease of installation.
- 330 watts RMS x 14 ohms
- preamp and speaker-level inputs
- variable bass boost
- The amp includes preamp- and speaker-level inputs,you can installin almost any vehicle, even one with a factory radio.
- MOSFET POWER SUPPLY: This powerful amplifier is outfitted with metal oxide semiconductor field-effect transistors that allow it to quickly switch from full to non-conduction operation for high efficiency...
- MAX POWER OUTPUT: 3000 watts into a single channel at 2 ohms. Maximum power output of 1250 watts into a single channel at 4 ohms. This amplifier is intended to power your subwoofer(s), giving them the...
- SLIM SIZE DESIGN: This amplifier has a slim design that makes it very convenient. It comes complete with all necessary mounting hardware for easy installation. This is very portable and lightweight to...
- VARIABLE BASS BOOST: Variable bass boost makes it easy to customize the low bass within the boost range to your preferences. Enhanced audio and bass, easy to use with user friendly controls. Reliable with...
- Ultra Compact MOSFET Monoblock Class D Car Amplifier
- RMS power @ 1 Ohm: 500 Watts x 1 Channel (14.4v)
- Frequency Response: 15Hz - 270Hz
- Hi-Level Input Connection: Yes | Signal-to-Noise Ratio (Sensitivity): 85dB
- Car audio amplifier 450 watts RMS at 2-ohm load (14.4v); 300 watts RMS at 4-ohm load (14.4v);
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 2-4 Ohm Stable - Able to continuously power loads of 2-4 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to...
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- 2000 W MAX Power @ 2 Ohm x 1 Channel
- 1000 W MAX Power @ 4 Ohm x 1 Channel
- High and Low Level Inputs
- Variable Low Pass Crossover, Variable Bass Boost
- Power - 1500 Max x 1 @ 2 Ohms, 700 Max x 1 @ 4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its...
- Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss &...
- Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- CLASS D, MONOBLOCK AMP: Deliver powerful sound to your speakers and subwoofers with this class D, 3,200-watt, monoblock car audio amplifier
- PLENTY OF POWER: Does 3200 watts x 1 channel at 1 ohm, 1600 watts x channel at 2 ohms, and 800 watts x channel at 4 ohms
- MINIMAL DISTORTION: Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion
- SECURE CONNECTIONS: Nickel-plated, high-temperature, impact-resistant design with hex screw terminals that allow for secure connections
- Power: 1 Channel Monoblock amplifier delivers 5000 watts max power to a single channel. No need to bridge, this is done internally in this car amplifier. 2000 watts of RMS power to your subwoofers.
- Strapable Operation: You can double the load by strapping 2 of these monoblock amplifiers to double your power output. These amps are durable and built to deliver monster power to your speakers.
- Build Specs: The OD1-5000D is built with a Military Grade PCB and with a PWM mosfet power supply. This amp also comes with direct short, thermal, & overload circuit protection to make sure your amplifier...
- In the Box: In the mono amp packaging you will find mounting brackets, a manual, bass knob and cable and of course a monster of an amplifier. Power Acoustik recommends professional installation and solid...
- Car audio amplifier with 2000 watts RMS power at 1-ohm load (14.4v); 1200 watts RMS at 2-ohm load (14.4v); 650 watts RMS at 4-ohm load (14.4v); Frequency response: 0 to 320 Hz (Bass Knob Included)
- Small footprint and compact chassis makes this mono amplifier easy to install in any vehicle or car audio application; but don’t let the size fool you, this 2000 watt amplifier absolutely pounds
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Powerful Performance: The AMP1501PRO delivers an impressive 563-watt RMS and a maximum output of 1500 watts, providing a significant power boost for a vibrant and dynamic driving soundtrack.
- Space-Efficient Design: With compact dimensions (7.1" x 7.5" x 2.1"), this amplifier seamlessly integrates into any trunk, optimizing space while delivering high-quality audio performance.
- High-pass and low-pass filters: integrated high- and low-pass filters on the rear panel allow you to set the crossover frequency between the subwoofer and speakers.
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
Last update on 2024-07-31 / Images Source Amazon Product API
Blog Post Related to Car Audio Amplifier Monoblock in Tampa, FL.
What is an Audiophile Car Stereo System?
Before we dive into what makes an audiophile car audio system, I think we need to define what an audiophile is. [...]
Are 10-Inch Subwoofers Loud Enough?
The world of car audio enthusiasts and home theater aficionados often revolves around a crucial question: Are 10-inch subwoofers loud enough? As [...]
Revealing the Secrets Of a Good Car Speaker
As we spend more time in our cars, the importance of a high-quality audio system becomes increasingly apparent. Whether you're a music [...]
Are Kenwood Speakers Any Good?
Kenwood is known for a lot of things, and thanks to how good the company has become, it’s now a leading face in a lot of areas. Kenwood started production in 1946 and established itself in Japan and later on in other countries. It has grown to become one of the most known brands of speakers for cars but has broadened its horizons towards home stereo units. So the question is, are Kenwood Speakers any good?
Well, let’s get into it.
Kenwood Speakers
Kenwood has a variety of speakers that you can pick from, such as high-power four-way speakers, two-way flush mount speakers, and three-way speakers. There are even five-way flush speakers.
These speakers have the capability to handle over 500 watts without blowing. The woofers are formed from polypropylene micro, which gives your music that boom bass. This way, you hear music free of distortion and background noise.
Performance
Kenwood usually has many speaker units with a range of features, such as butyl rubber, neodymium magnets, advanced crossover networks, and diamond array pattern diaphragms. These speakers allow for excellent power handling, and their sleek design gives them a very aesthetic look
Sound Quality
Another big deal for Kenwood Speakers is the sound quality. It offers Excelon that gives good sound range as well as sound quality. Note that these sound ranges differ according to the size and type of the speaker. Another thing that stands out is the durability of the speakers. You can be sure that you will go a very long time without changing any part of the speaker even if you live in harsh conditions.
Speaker Cone Construction
Kenwood was one of the first companies that started using urethane in speakers that optimizes cone movement when sound is getting reproduced. Additionally, the fiber-textured polypropylene is produced in such a way that they optimize strong lows and are great sounding.
There is also a speaker line produced by Kenwood with polypropylene mica composite cones and cloth edges. This is manufactured with a one-piece steel basket which means that durability is doubled because multiple pieces of steel wouldn’t loosen over time.
Compatibility and Pricing
One very nice thing about Kenwood Speakers is that it is made to be compatible with almost any car model. This way, any car amplifier will connect just fine to the speaker. This compatibility makes you able to connect your Kenwood Speaker to any system so far their OHMS and RMS ratings are compatible.
Additionally, their pricing is relatively affordable when compared to speakers of other brands, especially high-end brands. This way, you do not have to break the bank to enjoy the full range of Kenwood speakers’ capability. Also, like many speakers, Kenwood’s pricing is arranged according to frequency response and power handling.
Conclusion
To answer any extra questions, yes, Kenwood Speakers are good. Their sound production, durability, and price make them a good buy. They have been in the industry long enough and have truly made their mark.
Top Links Related to Car Audio Amplifier Monoblock in Tampa, FL.
There is no doubt that if looking for Car Audio Amplifier Monoblock in Tampa, FL you have many options. Even though, car manufactuerer’s like Bollinger Motors are making a lot more difficult to upgrade your car stereo you can still have a good sound system in your car, and we are certain that you will be able to find a local car stereo installation place Tampa, FL that it up to the task. We want to help you in this process be providing you the best deals on car stereo in or near Tampa, FL. From Dash Camera For Car to 8-Inch Car Subwoofer we got you covered. It is often said that music is the best way to change you mood and at ThunderEletronics.Net we want to be your go-to if looking for Car Audio Amplifier Monoblock in Tampa, FL…