Car Audio Amplifier Monoblock in McKinney, TX
If you’re looking Car Audio Amplifier Monoblock in McKinney, TX, you have to consider our car audio store. The reason a lot of audio enthusiasts stop by our site every month looking for things like car stereo bluetooth is not because we are the biggest but because stereo enthusiast who like to work in his/hers car knowt that our car audio outlet has a broad selection of stereos, speakers, subs, and amps.
Don’t matter if you’re searching for Car Audio Amplifier Monoblock McKinney, TX or Car Amplifier Wiring Kit we are confident you’ll find our variety suitable. That is because we put a lot of time and effort cooshing the products we offer so that you have the easiest car audio installation experience and a top notch car stereo system you can be proud of and your friends would want to purchase. So, tell all your friends for Car Audio Amplifier Monoblock in McKinney, TX take a look at Thunder Eletronics for great prices and top brands for Car Audio Amplifier Monoblock in McKinney, TX or Preloaded Subwoofer Boxes we’re sure you’ll pleased with the seletion at ThunderElectronics.Net. For the best selection on 10-inch car subwoofer box and fast expedited shipping, and no six for a nine games you can count on Thunder Electronics!
Best Selling Car Audio Amplifier Monoblock Near McKinney, TX
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 1,600 Watts | RMS Power at 1 Ohm: 1,200 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 4 Gauge Power & Ground Input Terminals for Maximum Current Flow. Damping Factor - 150
- Power - 1100 Max x 1 @ 2 Ohms, 550 Max x 1 @ 4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its...
- MOSFET Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss &...
- Low & High Level Inputs - A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your...
- Blaupunkt 1500 Watt Monoblock Amplifier
- Max power output: 1500 watts / RMS Output Power Rating: 4 ohms: 120 watts x 1 channel / 2 ohms: 200 watts x 1 channel / Frequency Response: 10Hz - 30kHz
- Signal-To- Noise Ratio: >96 dB / Voltage Supply: 11 - 16V DC / Gain Adjust: 200mV-8V
- Total Harmonic Distortion:
- 4,000 watts x 1 channel max power output
- 2,800 watts RMS x 1 channel at 1 ohm
- 2,000 watts RMS x 1 channel at 2 ohms
- 1,000 watts RMS x 1 channel at 4 ohms
- 3,000 watts x 1 channel max power output
- 198 watts RMS x 1 channel at 4 ohms
- 396 watts RMS x 1 channel at 2 ohms
- Designed to power vehicle subwoofer
- Car audio amplifier with 1500 watts RMS power at 1-ohm load (14.4v); 850 watts RMS at 2-ohm load (14.4v); 450 watts RMS at 4-ohm load (14.4v); Frequency response: 0 to 320 Hz (Bass Knob Included)
- Small footprint and compact chassis makes this mono amplifier easy to install in any vehicle or car audio application; but don’t let the size fool you, this 1500 watt amplifier absolutely pounds
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Power - 2000 Watts MAX x 1 @1-Ohm, 1000 Watts RMS x 1 @1-Ohm, 650 Watts RMS x 1 @2-Ohms,400 Watts RMS x 1 @4-Ohms
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be...
- To keep both your car and the stereo amp safe, this ZE1000.1 is equipped w/ thermal, overload and short circuit protection. Has been specially designed from the bottom up to provide safe and high quality...
- Class D MOSFET Monoblock Power Amplifier
- Peak Power at 1 Ohm: 388 Watts | RMS Power at 1 Ohm: 350 Watts
- Frequency Response: 20Hz - 250Hz, On-board Bass EQ Switch with +6 or +12dB boost at 45Hz
- Featuring 4-Way Protection Circuitry and 8 AWG Power & Ground Input Terminals for Maximum Current Flow
- By Orion High Performance Car Audio
- CBT4500.1D Cobalt Series 1-Channel Monoblock Class D Amplifier
- Watts @ 1 Ohm Mono 14.4V: 1200W
- Max Music Peak Power: 4500W
- Digital Class-D Mono Block Amplifier: Class D topology ensures high efficiency with big power and a small footprint. This mono amplifier was built for driving subwoofers and subwoofer systems, maintaining...
- Small Footprint and Sturdy Design: Made it precision metal potentiometer for precise tuning and sturdy construction.
- Robust Unregulated Power Supplies: The power supply circuitry adopts advanced pulse width modulator integrated circuits that are designed to offer improved performance and efficiency.
- Remote Bass Controller Included: Provides remote level control of bass from listening position. With a sleek flush-mount knob for ease of installation.
- 330 watts RMS x 14 ohms
- preamp and speaker-level inputs
- variable bass boost
- The amp includes preamp- and speaker-level inputs,you can installin almost any vehicle, even one with a factory radio.
- MOSFET POWER SUPPLY: This powerful amplifier is outfitted with metal oxide semiconductor field-effect transistors that allow it to quickly switch from full to non-conduction operation for high efficiency...
- MAX POWER OUTPUT: 3000 watts into a single channel at 2 ohms. Maximum power output of 1250 watts into a single channel at 4 ohms. This amplifier is intended to power your subwoofer(s), giving them the...
- SLIM SIZE DESIGN: This amplifier has a slim design that makes it very convenient. It comes complete with all necessary mounting hardware for easy installation. This is very portable and lightweight to...
- VARIABLE BASS BOOST: Variable bass boost makes it easy to customize the low bass within the boost range to your preferences. Enhanced audio and bass, easy to use with user friendly controls. Reliable with...
- Ultra Compact MOSFET Monoblock Class D Car Amplifier
- RMS power @ 1 Ohm: 500 Watts x 1 Channel (14.4v)
- Frequency Response: 15Hz - 270Hz
- Hi-Level Input Connection: Yes | Signal-to-Noise Ratio (Sensitivity): 85dB
- Car audio amplifier 450 watts RMS at 2-ohm load (14.4v); 300 watts RMS at 4-ohm load (14.4v);
- Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced...
- 2-4 Ohm Stable - Able to continuously power loads of 2-4 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to...
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- 2000 W MAX Power @ 2 Ohm x 1 Channel
- 1000 W MAX Power @ 4 Ohm x 1 Channel
- High and Low Level Inputs
- Variable Low Pass Crossover, Variable Bass Boost
- Power - 1500 Max x 1 @ 2 Ohms, 700 Max x 1 @ 4 Ohms
- Class A/B Topology - Class ‘A’ amplifiers have enormous amount of current flowing through its output transistors with no audio signal. Class ‘B’ amplifiers have no current flowing through its...
- Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage & current precisely by removing the output current sensing loss &...
- Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
- CLASS D, MONOBLOCK AMP: Deliver powerful sound to your speakers and subwoofers with this class D, 3,200-watt, monoblock car audio amplifier
- PLENTY OF POWER: Does 3200 watts x 1 channel at 1 ohm, 1600 watts x channel at 2 ohms, and 800 watts x channel at 4 ohms
- MINIMAL DISTORTION: Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion
- SECURE CONNECTIONS: Nickel-plated, high-temperature, impact-resistant design with hex screw terminals that allow for secure connections
- Power: 1 Channel Monoblock amplifier delivers 5000 watts max power to a single channel. No need to bridge, this is done internally in this car amplifier. 2000 watts of RMS power to your subwoofers.
- Strapable Operation: You can double the load by strapping 2 of these monoblock amplifiers to double your power output. These amps are durable and built to deliver monster power to your speakers.
- Build Specs: The OD1-5000D is built with a Military Grade PCB and with a PWM mosfet power supply. This amp also comes with direct short, thermal, & overload circuit protection to make sure your amplifier...
- In the Box: In the mono amp packaging you will find mounting brackets, a manual, bass knob and cable and of course a monster of an amplifier. Power Acoustik recommends professional installation and solid...
- Car audio amplifier with 2000 watts RMS power at 1-ohm load (14.4v); 1200 watts RMS at 2-ohm load (14.4v); 650 watts RMS at 4-ohm load (14.4v); Frequency response: 0 to 320 Hz (Bass Knob Included)
- Small footprint and compact chassis makes this mono amplifier easy to install in any vehicle or car audio application; but don’t let the size fool you, this 2000 watt amplifier absolutely pounds
- Engineered to be the most efficient car monoblock amplifier in its class so that you can get the most out of your vehicle’s electrical system
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
- Powerful Performance: The AMP1501PRO delivers an impressive 563-watt RMS and a maximum output of 1500 watts, providing a significant power boost for a vibrant and dynamic driving soundtrack.
- Space-Efficient Design: With compact dimensions (7.1" x 7.5" x 2.1"), this amplifier seamlessly integrates into any trunk, optimizing space while delivering high-quality audio performance.
- High-pass and low-pass filters: integrated high- and low-pass filters on the rear panel allow you to set the crossover frequency between the subwoofer and speakers.
- MOSFET pulse width modulated power supply and proprietary heat dissipation design will ensure the amplifier for car subwoofers runs cool for even the most demanding playlists
Last update on 2024-07-31 / Images Source Amazon Product API
Blog Related to Car Audio Amplifier Monoblock in McKinney, TX.
Tell-Tell Signs of a Good Sounding Car Speaker
When it comes to car audio and car audio speakers, one should never consider buying them without listening to them. Preferably in a [...]
Does Kicker Make Competition Speakers?
Kicker is a known brand that has been making speakers since 1973. They started as a two-person operation in a garage with nothing [...]
Are Kicker Subwoofers Any Good?
There are several types, sizes, and brands to choose from when looking for an excellent automobile subwoofer. The Kicker is one of the [...]
Buick Grand National Car Stereo System
Since I was in high school, I always wanted to have a Buick Grand National. Maybe it is just me, but I always thought that car looked super mean. And yes, while Buicks are considered a grandma’s car those who know what a Grand National can do, will say to the contrary. Now that I have the means, I decided to find myself a Buick Grand National. After finding one in perfect condition, I went ahead and purchased it.
Since acquiring my mean black Buick, I’ve done a little bit of work on the engine. I have upgraded the turbo, install an oversize intercooler, added a high-pressure fuel pump, aftermarket wastegate, a new computer, and several other upgrades including wheels tires, suspension, and exhausts. I have to say that I like my car. However, the sound system sucks. If you’re not familiar with this car it came with a Delco 1.5 DIN cassette radio, 3 1/2 inch speakers in the dash, and 4×10 speakers in the rear deck.
As you can imagine, this is no match for the 650 horsepower engine under the hood. The problem is that with these speaker cavities, what can you do? The first thing I did was stop by car audio near me places looking for experienced installers, familiar with this vehicle. That did not work! It seems like kids nowadays are just interested in boomy car stereo systems.
After asking around, I was able to locate an old-timer who claimed to have competed in car audio with a similar vehicle. At the end of the day, I ended up having custom door panel pods built. Unlike many door pods, I had these made, so that lay over the factory door panel, and that can get removed the day I want to sell the car.
Just to be clear, I am not rich, and everything I do has a budget! So with that said I know there are people out there who are going to say that I could have done much better, and maybe will upgrade in the future but taking into consideration where I am coming from this is a huge upgrade.
The system consists of a Rockford Fosgate 5-Channel amp mounted on a custom rank that contours the left side of the truck wall being fed by the Alpine CDE-163BT Advanced Bluetooth CD Receiver. I know that nowadays kids are into everything Bluetooth. To be honest with you I don’t care much about the Bluetooth,” type of guy has to believe in the quality of the CD. The fact is until somebody can show me an MP3 with a 16-bit/44.1kHz resolution I will be sticking to CDs. I did not use the front speaker location which houses a 3 1/2 inch woofer. Instead, I opted for a pair of Q-Logic kick panels and mounted the Pioneer TS-D1330C 5.25″ D-Series Component Speaker Package on it. I chose the NEUPRO 65 V2 4 from Sundown Audio for the custom door panel. That is a 6.5″ 4-Ohm Midrange Speaker that is very shallow, and with an excellent midbass snap to it! The midbass is further enhanced because the door pod enclosure is sealed.
For the back speakers, I also avoided the factory location. Instead, I opted to use the panels above the hand rest for the rear seat. After making custom plates, I mounted a set of Pioneer TS-D1730C 6 3/4″ component speakers with the woofer in the custom plate and the tweeter flush-fitted to the side panel all the way back near to the rear window. For subs, I decided to use two Pioneer Free 12″ subs. I fabricated a reverse box with the back open and sealed against the back seat wall. You may question this, but if you hear it you agree it was the best choice.
Trending Links Related to Car Audio Amplifier Monoblock in McKinney, TX.
Without a question that if searching for Car Audio Amplifier Monoblock in McKinney, TX you have many options. Although, car manufactuerer’s like Hummer are making a lot more difficult to upgrade your car stereo you can still have a good sound system in your vehicle, and we‘re positive that you can find a professional car audio installation store McKinney, TX that it up to the task. At Thunder Electronics we want to make this process easier be offering you the best deals on car audio in or near McKinney, TX. From Car Audio Equalizer to Car Audio Speaker 4 Inch we got you covered. It is often said that music is the best medicine there is and at ThunderEletronics.Net we want to be your best option when looking for Car Audio Amplifier Monoblock in McKinney, TX…